- #GEARHEAD GARAGE WINDOWS 7 FIX HOW TO#
- #GEARHEAD GARAGE WINDOWS 7 FIX CRACKED#
- #GEARHEAD GARAGE WINDOWS 7 FIX INSTALL#
With the motor assembly held or supported in this position, raise and lower the garage door by hand to be sure that the rail location does not interfere with the door's movement.
Step 5: Raise the motor assembly to the point where the rail is horizontal, or parallel with the door track. Be sure to use washers under the heads of the bolts to keep them from pressing into the wood. If bolts and nuts are provided, however, you must drill suitable holes through the front mounting plank. The rail bracket provided for this purpose usually fastens to the front mounting plank with lag screws. With the garage door down, lift and fasten the outermost end of the rail to the front mounting plank at a location about two inches above the intersecting marks you made for your door's high point and center line. Step 4: Attach the rail to the motor unit on the garage floor, following the procedure outlined in the kit instructions. Transfer your high-point mark to this plank, and extend the vertical door center line onto the plank as well. Center and fasten a length of 2 X 6-inch plank securely with lag screws across two wall studs over your mark of highest door travel.
#GEARHEAD GARAGE WINDOWS 7 FIX INSTALL#
If your garage lacks a structural member in that location, install a front mounting board. Step 3: Inspect the area right above the garage door at your vertical dividing line there must be a support in that location suitable for attaching the front end of the rail.
Otherwise, as the door opens, it could strike the rail. Mark this location, because you must mount the opener so that the rail is higher than the peak of the door's travel. Step 2: Raise and lower the door, observing the top point of its travel. When you affix the drawbar (the mechanism for raising and lowering the door) at this line, the door weight will be evenly balanced at the lifting point. On the inside of the door, toward the top, draw a short vertical line down the center of the door. To determine the location, use a tape measure to figure the width of the garage door. Step 1: The mechanism should be installed at the center of the door.
#GEARHEAD GARAGE WINDOWS 7 FIX HOW TO#
Here's how to install a garage door opener: If possible, move the hinge onto solid wood. Let the filler dry and then replace the hinge.
#GEARHEAD GARAGE WINDOWS 7 FIX CRACKED#
If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. Sagging at one side of the door can often be corrected by servicing the hinges. On roll-up doors, check the hinges that hold the sections of the door together tighten any loose screws, and replace any damaged hinges. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. Step 5: Check for loose hardware, and tighten as needed. Clean the rollers thoroughly, and wipe both tracks and rollers dry. Step 3: Clean the tracks with concentrated household cleaner to remove dirt and hardened grease. Recheck the tracks with the level to make sure they're in the right position then tighten the screws or bolts at the mounting brackets. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Both tracks must be at the same height on the garage walls. Horizontal tracks should slant slightly down toward the back of the garage with roll-up doors, the vertical sections of track should be exactly plumb. Step 2: Check the tracks with a level to make sure they're properly aligned. If the tracks are badly damaged, they should be replaced. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If they're loose, tighten the bolts or screws at the brackets. Look at the mounting brackets that hold the tracks to the walls. Step 1: Check the metal tracks inside the garage.